AMPANO

Physical AI for engineers.

AMPANO is an AI engineering platform designed to help engineers trace how a change in a drawing or 3D model affects the system it describes.

Explore the engineering examples

THE CHALLENGE

A duct can fit above a ceiling and still deliver too little air.

Move a branch around a beam and the clash disappears from the plan. The extra bend changes the pressure loss. Before signing off, the engineer still has a question to answer. Will the last room get the air it needs?

HOW AMPANO WORKS

Drawing → Physics → Validation

The role we see for AI is to identify the part an engineer has changed and the calculations that depend on it. The ventilation engine gives an assistant a concrete way to follow those dependencies.

  1. Locate the change

    A duct and its terminals have identities in the network model. A change of section belongs to a particular branch.

  2. Recalculate the effect

    For a specified airflow, the engine calculates pressure losses in the modelled network. An edit makes the affected results due for recalculation.

  3. Review the revision

    The engineer can check the revised drawing and its calculation together. Revision checks prevent an earlier result from being carried forward as current.

BUILDING SERVICES · VENTILATION

From floor plan to duct layout.

The ventilation engine routes ducts on supported sample networks and calculates losses at specified airflows. This prepared six-room example illustrates the routing workflow. Follow the cyan reference line to see where the layouts diverge.

SUPPLY VENTILATIONSAMPLE FLOOR PLAN
ILLUSTRATIVE DATAFloor plan

How the route is built

Read the plan

Use the architectural drawing and task brief to identify served rooms, constraints and airflow requirements.

Route the system

Place terminals and connect them to the main duct. Inspect which rooms each branch serves.

Compare the result

Overlay a reference design and see where the routes align or diverge before reviewing the CAD output.

THERMAL MACHINERY · GAS TURBINE

How much power reaches the shaft?

In this illustrative study, follow the shaft from the compressor to the generator, then find those components in the cutaway. The power estimate uses the work left after driving the compressor. All three views describe the same machine.

01 / DRAWINGGT-01 · Functional schematic
Functional schematic of the GT-01 gas turbine installation Air passes through the inlet filter, compressor and combustor, then expands through the turbine to exhaust. The turbine shaft drives the compressor and generator. Separate fuel and lubricating oil circuits serve the combustor and shaft bearings. The sheet also marks compressor discharge pressure, exhaust temperature, the oil cooler and the generator breaker. PTTT FUEL IN FILTER METERING AIR INEXHAUST C-01 COMPRESSOR B-01 COMBUSTOR T-01 TURBINE G-01 GENERATOR ELECTRICAL OUT CB-01 COMMON SHAFT OIL TANK PUMP HX-01 OIL SUPPLY OIL RETURN
02 / CALCULATIONShaft power
Mass flow
20 kg/s
Net specific work
60 kJ/kg

20 kg/s × 60 kJ/kg

1.20 MW

Illustrative steady-state estimate

03 / MODELGT-01 · Gas turbine cutaway · 1.20 MW
Conceptual gas turbine cutaway with airflow passing through the compressor, combustor and turbine C-01 COMPRESSORB-01 COMBUSTORT-01 TURBINE AIR INTAKEEXHAUST
Gas turbine system The schematic shows the gas path, fuel and oil circuits, and the generator connection. The calculation estimates shaft power, and the cutaway shows the compressor, combustor and turbine assembly.

ELECTRICAL SYSTEMS · WIND & STORAGE

How long can the battery supply the grid?

This illustrative study follows the battery from its symbol on the single-line drawing to its location on site. The three generators determine installed wind capacity. A separate duty requirement determines how much usable energy the battery must store.

01 / DRAWINGWF-01 · Electrical single-line
Electrical single-line diagram with three wind generators connected to a collector bus, a battery coupled through a bidirectional inverter, and a grid connection G-01G-02G-03 COLLECTOR BUSBIDIRECTIONAL INVERTER BESS-01GRID
02 / CALCULATIONGeneration and storage
Wind nameplate
3 × 2 MW
Storage duty
2 MW × 2 h

6 MW / 4 MWh

Illustrative installed power / usable storage target

03 / MODELWF-01 · Site arrangement · 6 MW / 4 MWh
Wind turbines supplying a grid connection and charging a battery storage system G-01 / G-02 / G-03 BESS-01 GRID CONNECTION
Wind and battery storage The single-line drawing shows the connections. The calculation gives installed power and a storage target, and the site model places the same equipment in space.

INDUSTRIES

Engineering across physical systems.

Across buildings, heat networks and power systems, AMPANO’s focus is to link a design choice to a quantity an engineer can check.

Building services
Connect a proposed duct route to room airflow requirements, pressure losses and the constraints of the building plan.
Industrial and district heating
In a heat network, a change in pipe size raises questions about flow, pressure loss and heat delivery. These are the quantities a piping model needs to carry.
Power generation and storage
Trace shaft power through a gas turbine or follow electricity from wind generators to storage and the grid.

OUR VISION

Give every design a way to prove itself.

A design should carry the reasoning behind it. When a duct changes size, the engineer reviewing the drawing should be able to find the affected branch, the airflow assumed there and the pressure calculation that needs another look. That is the kind of engineering context an AI assistant should understand.

For a battery, the trail runs from a 4 MWh storage target back to a requirement for 2 MW over two hours. For a CFD result, it leads to the geometry revision and boundary conditions used in the simulation. Our aim is for the engineer who inherits a model to know why the team chose that design and what to revisit when the brief changes.

Building chilled-water loop Water flows from the chiller through a pump to the cooling coil, absorbs heat from the building air, and returns to the chiller. ChillerCooling coil SupplyReturn